What are the spacing requirements for PCB designing？

PCB engineers in doing PCB design, often encounter a variety of safety spacing problems, usually these spacing requirements are divided into two categories, one is the electrical safety spacing, the other is: non-electrical safety spacing. So, what are the spacing requirements for designing PCB circuit boards?

First, the electrical safety spacing

1 the spacing between the wires: the minimum line spacing, also line-to-line, line-to-pad spacing shall not be less than 4 MIL. from the production point of view, the greater the better, of course, when available. The general routine 10MIL is more common.

2 pad aperture and pad width: according to PCB manufacturers, pad aperture if the mechanical drilling method, the minimum shall not be less than 0.2mm; if the laser drilling method, the minimum shall not be less than 4mil. and aperture tolerance according to different plates slightly different, generally can be controlled within 0.05mm; pad width of the minimum shall not be less than 0.2mm.

3 the spacing between the pads and pads: according to PCB manufacturers processing capabilities, the spacing shall not be less than 0.2MM.

4 the spacing between the copper skin and the board edge: preferably not less than 0.3mm. If it is a large area of copper laying, usually with the edge of the board has an inward shrinkage distance, generally set to 20mil.

Second, non-electrical safety spacing

1 the width and height of the characters and spacing: on the screen printing characters generally use conventional values such as: 5/30, 6/36 MIL, etc.. Because when the text is too small, processing printing out will be blurred.

2 screen printing to the pad distance: screen printing is not allowed on the pad. Because if the silk screen on the pad, the silk screen will not be able to tin at the time of tin, thus affecting the components mounted. General PCB manufacturers require 8mil spacing. If some PCB board area is very tight, to do 4MIL spacing is also acceptable. If the screen printing in the design accidentally cover the pad, PCB manufacturers in the manufacturing will automatically eliminate the part of the screen printing on the pad to ensure that the pad on the tin.

3 the 3D height and horizontal spacing on the mechanical structure: PCB devices in the installation and paste, to take into account the horizontal direction and space height will not have conflicts with other mechanical structures. Therefore, the design should be fully considered between the components, as well as between the finished PCB and the product shell, the adaptability of the spatial structure, to reserve a safe spacing for each target object.

Comments

The biggest problem with the latest 56 semiconductor manufacturers suspend orders, price increased, and long lead time. How can you fix it?

Following the suspension of MCU orders by ELAN , Holtek Semiconductor issued a notice on 21st April suspending orders with immediate effect. The price of various semiconductors, especially MCUs, has risen as a result of factors such as the tightness of 8-inch wafer foundries. The demand for MCUs is so high that many major MCU manufacturers at home and abroad are operating at full capacity, but supply still exceeds demand. In its notice, Holtek Semiconductor stated that Suspension of orders for 2022 Subject: Orders with delivery dates in 2022 are suspended with immediate effect. Description: 1. The wafer fabs and packaging houses have advised that there will be another wave of price increases soon - price increases of 15%-30%. 2. The fabs are expected to provide 2022 production numbers by early May and will announce 2022 order acceptance rules when confirmed. 3. expected to resume accepting orders for 2022 by mid-May. 4. 2022 orders that have received deposits will be rescheduled

Understanding of DC-DC buck bootstrap circuit

In the peripheral circuit design of DC-DC BUCK chips, we usually add capacitors or a combination of capacitors + resistors between the BOOT and SW pins, this piece of circuit is called bootstrap circuit, the capacitors and resistors in the bootstrap circuit are called bootstrap capacitors and bootstrap resistors. What is a bootstrap capacitor? DCDC Buck chip has a pin called BOOT, and some are called BST. The following is an explanation of the BOOT pin of a DCDC chip. In the external circuit design, a capacitor, generally 0.1uF, is needed between the BOOT and SW pin, and is connected to the driver end of the high-end MOS tube of DCDC. How does a bootstrap capacitor work? The following is a block diagram of a DCDC BUCK chip, the top NMOS is called the high-side MOSFET and the bottom NMOS is called the low-side MOSFET. When the high side MOS tube is turned on, SW is VIN, SW charges and stores energy in the inductor, and the inductor current is rising; when the low side MOS

2022 global chip shortage continues: ST、NXP、ADI、XILINX、ONSEMI、DIODES... latest trends

Under the influence of the epidemic and various emergencies around the world, the global chip industry fell into a shortage of stock in 2021. Now it has been a year, and the shortage of chips seems to have not eased. Below, we have collated the latest market developments of the original chip manufacturers such as ST, Renesas, NXP, ADI, ON Semiconductor, Microchip, Qualcomm, etc., so that you can have a good idea of the market situation. ST: Large shortage of high-end products and automotive chips Most stockists have been selling off since the prices of ST products have fallen back, but this month has seen a small rebound. For example, STM8S003F3P6TR and STM32F103VCT6 , two pieces of material, have seen a small price increase. It is worth noting that the market price of ST's brake system chips has recently soared, and other automotive chips have also risen, and there is still a large shortage of high-end products and automotive chips, and delivery times are still long. In additi

Teach you 5 ways to identify and avoid counterfeit electronic components in a second

In the process of purchasing electronic components, the most worrying thing for buyers is not the price, but the quality of the product. There are a variety of IC chips on the market, of all kinds, and without paying attention to the distinction, it is sometimes difficult to see the difference between various materials, whether it is true or false, new or refurbished. The following is a compilation of some methods to identify genuine and fake chips, for your reference. Common chip counterfeiting methods Material A counterfeit material A Original manufacturer's tailor loose material: the original packaging has been disassembled or is no longer available, but product functionality and yield may be lower due to storage time or handling process, etc. Original manufacturer scrap or defective products: mainly products that have not passed factory inspection by the original manufacturer, such as scrap products after reliability testing, poor packaging quality, bad test products, etc. Orig

9 effective ways to improve your electronic components specification for approval

1. Let purchasers find manufacturers to provide specifications, safety information, environmental protection information, insurance information - E-document 2. Verify that the information is true and complete, such as the applicable period of the document, so as not to be fooled by the manufacturer. 3. Let the buyer find the manufacturer to provide samples, specifications, safety information, environmental information, insurance information - Paper files 4. Environmental test: send several samples to the environmental laboratory for ROSH halogen test. 5. Electrical specifications and high-temperature testing - e.g. electrolytic capacitors : A: measuring capacity and deviation withstand voltage, PIN foot tin is good B: go through the production line to see if the capacitors are deformed after the high temperature of the furnace and if the capacity and the deviation voltage are okay. 6. Body size check - e.g. electrolytic capacitors . Body height and diameter, PIN pin spacing, PIN pin d

Seektronics

Search This Blog