How Do You Design Via In Pad In PCB? The Right Way

Via in pad as the name implies, is to hit the hole in the pad, with the increasing integration of electronic products, the components package is getting smaller and smaller, especially in complex PCB design pin spacing is too small, not hit the plate in the hole can not fan out, then you must hit the plate in the hole, from the next layer out of the line.

In the drawing of the PCB, the plate in the hole is nothing special, is over the hole in the pad, but there are several types of PCB production and processing processes, as hardware engineers must understand.

The most common hole in the plate

Is the hole in the pad, the production of PCB does not require a special process, the pad will leave a "hole eye", if the hole eye is too large may cause tin leakage problems, may also lead to false soldering problems, this process is the cheapest and most common, as follows QFN package on the heat sink hole.

Resin plugging hole + copper plating cap

This type of plate-in-the-hole process is a little more complex, first in the hole filled with epoxy resin, and then electroplated copper seal, the surface can not see the hole eye, very flat, there will be no tin leakage or false soldering problems, this process is generally used in the higher-end some HDI board, such as the board to go on high-precision devices, such as BGA and other pin devices, pin spacing is too small to fan out, the surface out of the line is difficult, need to go through the hole To the next layer out of the line, this plate in the hole has a great advantage, so that the alignment is smooth. Compared with the ordinary plate in the hole process is relatively complex, of course, the cost will also increase. Now the cell phone board is in the plate hole design.

Copper paste hole plugging + electroplated copper cap

This type of plate-in-the-hole process is generally used in the need for rapid thermal conductivity of the location, such as the QFN under the GND PAD. over the hole in the middle of the plug filled with copper paste, and then an electric copper seal. Since the middle of the hole is filled with copper metal, the thermal conductivity is very good, and there is no difference between the resin plug hole from the surface. This process can be used when a large amount of heat dissipation is required for the QFN, which is so flat that the naked eye cannot see any traces of over-hole after production. Heat dissipation performance is particularly good. Of course, you get what you pay for, the process is quite good, but more expensive.

Comments

The biggest problem with the latest 56 semiconductor manufacturers suspend orders, price increased, and long lead time. How can you fix it?

Following the suspension of MCU orders by ELAN , Holtek Semiconductor issued a notice on 21st April suspending orders with immediate effect. The price of various semiconductors, especially MCUs, has risen as a result of factors such as the tightness of 8-inch wafer foundries. The demand for MCUs is so high that many major MCU manufacturers at home and abroad are operating at full capacity, but supply still exceeds demand. In its notice, Holtek Semiconductor stated that Suspension of orders for 2022 Subject: Orders with delivery dates in 2022 are suspended with immediate effect. Description: 1. The wafer fabs and packaging houses have advised that there will be another wave of price increases soon - price increases of 15%-30%. 2. The fabs are expected to provide 2022 production numbers by early May and will announce 2022 order acceptance rules when confirmed. 3. expected to resume accepting orders for 2022 by mid-May. 4. 2022 orders that have received deposits w...

Understanding of DC-DC buck bootstrap circuit

In the peripheral circuit design of DC-DC BUCK chips, we usually add capacitors or a combination of capacitors + resistors between the BOOT and SW pins, this piece of circuit is called bootstrap circuit, the capacitors and resistors in the bootstrap circuit are called bootstrap capacitors and bootstrap resistors. What is a bootstrap capacitor? DCDC Buck chip has a pin called BOOT, and some are called BST. The following is an explanation of the BOOT pin of a DCDC chip. In the external circuit design, a capacitor, generally 0.1uF, is needed between the BOOT and SW pin, and is connected to the driver end of the high-end MOS tube of DCDC. How does a bootstrap capacitor work? The following is a block diagram of a DCDC BUCK chip, the top NMOS is called the high-side MOSFET and the bottom NMOS is called the low-side MOSFET. When the high side MOS tube is turned on, SW is VIN, SW charges and stores energy in the inductor, and the inductor current...

2022 global chip shortage continues: ST、NXP、ADI、XILINX、ONSEMI、DIODES... latest trends

Under the influence of the epidemic and various emergencies around the world, the global chip industry fell into a shortage of stock in 2021. Now it has been a year, and the shortage of chips seems to have not eased. Below, we have collated the latest market developments of the original chip manufacturers such as ST, Renesas, NXP, ADI, ON Semiconductor, Microchip, Qualcomm, etc., so that you can have a good idea of the market situation. ST: Large shortage of high-end products and automotive chips Most stockists have been selling off since the prices of ST products have fallen back, but this month has seen a small rebound. For example, STM8S003F3P6TR and STM32F103VCT6 , two pieces of material, have seen a small price increase. It is worth noting that the market price of ST's brake system chips has recently soared, and other automotive chips have also risen, and there is still a large shortage of high-end products and automotive chips, and delivery times are still long. ...

Teach you 5 ways to identify and avoid counterfeit electronic components in a second

In the process of purchasing electronic components, the most worrying thing for buyers is not the price, but the quality of the product. There are a variety of IC chips on the market, of all kinds, and without paying attention to the distinction, it is sometimes difficult to see the difference between various materials, whether it is true or false, new or refurbished. The following is a compilation of some methods to identify genuine and fake chips, for your reference. Common chip counterfeiting methods Material A counterfeit material A Original manufacturer's tailor loose material: the original packaging has been disassembled or is no longer available, but product functionality and yield may be lower due to storage time or handling process, etc. Original manufacturer scrap or defective products: mainly products that have not passed factory inspection by the original manufacturer, such as scrap products after reliability testing, poor packaging quality, bad test products, etc. Orig...

9 effective ways to improve your electronic components specification for approval

1. Let purchasers find manufacturers to provide specifications, safety information, environmental protection information, insurance information - E-document 2. Verify that the information is true and complete, such as the applicable period of the document, so as not to be fooled by the manufacturer. 3. Let the buyer find the manufacturer to provide samples, specifications, safety information, environmental information, insurance information - Paper files 4. Environmental test: send several samples to the environmental laboratory for ROSH halogen test. 5. Electrical specifications and high-temperature testing - e.g. electrolytic capacitors : A: measuring capacity and deviation withstand voltage, PIN foot tin is good B: go through the production line to see if the capacitors are deformed after the high temperature of the furnace and if the capacity and the deviation voltage are okay. 6. Body size check - e.g. electrolytic capacitors . Body height and diameter, PIN pin spacing, PIN p...

Seektronics

Search This Blog